inlet parameter
英 [ˈɪnlet pəˈræmɪtə(r)]
美 [ˈɪnlet pəˈræmɪtər]
【化】入口参数
双语例句
- With adoption of the typical flue gas inlet parameter for FGD, this article completes above calculation with humidity and pressure volume heat concept, and analyzes the relative changing rules.
计算采用典型FGD入口烟气参数，应用烟气湿度和定压容积热容的概念计算了吸收塔出口烟气温度及塔内蒸发水量，并分析了其变化规律。 - Temperature difference of cooling water between inlet and outlet from calculation is in good agreement with measured data and this validates the rationality of model and parameter.
计算得到的冷却水进出口温差随冶炼时间的变化与现场实测结果吻合，进一步验证了所建模型和参数选择的合理性。 - Augmenting the gas velocity in the center of the distributor, optimizing the inlet position of the condensed liquid and enhancing the accuracy of the operation parameter monitoring are pointed out.
指出需要增强分布板中心区域的气速，改善冷凝液的进料位置，提高在线监测的准确度。 - These conclusions offer basises for rational design of the inlet structure and its parameter on hydrocyclone.
这些结论为水力旋流器入口结构及参数的合理设计提供了依据。 - Based on the experimental results, a new relational expression for pressure drop during flow boiling of water in a horizontal micro-tube, integrating the dimentionless inlet temperature parameter, is set up and its veracity is less than 12.2%.
因此，结合无量纲进口温度参数建立了新的微管内水流动沸腾的压降关联式，其预测实验结果的误差在12.2%以内。 - Based on measured fuel injection rates and heat release rates for various matching of combustion chamber, injection system and inlet port, effects of each construction parameter on combustion behavior were discussed, and optimal matching requirements were outlined.
作者根据燃烧室、喷油系与进气道多种不同匹配方案的实测喷油规律与燃烧放热规律，分析了各种结构参数对燃烧特性的影响，并指出优化匹配的要点。 - The optimized structure of the separators was obtained by analyzing the numerical simulation result, and the influences of suction velocity on the flow field and particle separation was analyzed by changing the inlet parameter of the separators.
分析数值模拟结果得到了内置组合式高温旋涡分离器的优化结构，并通过改变分离器入口参数，分析了入口速度对流场及颗粒分离的影响。 - Meanwhile the influences of inlet parameter X1 are also discussed.
另外还对入口参数X1对相分离效果的影响进行了计算和分析。 - The result indicates that temperature at the inlet of catalyst bed is the most optimal control parameter to realize the optimal operation of ammonia converter.
结果表明，催化床进口温度是实现氨合成塔优化操作的最优调节参数。 - [ 3]. The paper also points out that the inlet temperature of the turbofan after& burner is low and the temperature exponent of the stability parameter may be smaller than 1.
本文还指出涡轮风扇加力室进口温度低，稳定准则中的温度指数可能小于1。 - It is shown that the particle separation diameter increases with the increase of the cone angle and hydrocyclone diameter, while decreases with the increase of inlet pressure in the parameter range considered.
数值结果表明，在高炉污泥颗粒分离的应用范围内，锥角增大，旋流器直径增大，分离粒径会增加，进口压力增加，分离粒径降低。 - On this basis, performances prediction of the AC in different inlet air parameter has been done.
在此基础上，预测空调器在不同空气侧进风参数下的各项性能指标。 - The simulation of 2100 diesel engine inlet port in steady flow rig is studied in this dissertation. Some important issues are discussed such as how to establish the model, how to draw the compute grid and the ways to evaluate the performance parameter of inlet port.
本文以2100柴油机切向进气道为例探索了使用计算机模拟进气道稳流试验及其性能评价的方法，并详细阐述了模型的建立、网格的划分以及气道性能的评价方法。 - A Bond Graph Model of Inlet Flow and Outlet Flow for the Distributed Parameter Fluid Transmission Line and its Experimental Research
输入流输出流管道分布参数键图模型的建立与实验研究 - When inlet parameter is the same, the length of rectangular has little effect on CHF;
在入口参数相同时，即相同的入口过冷度和质量流速式矩形通道的长度对临界热流密度的影响较小； - The influence of inlet parameter and configuration and cold air fraction on the vortex board performance was investigated by experiment with air as a medium.
用实验方法研究了入口参数和冷流比对涡流板能量分离特性的影响。 - That the inlet matched the impeller was the main factor inflecting the flow velocity distribution and vortex flow at the blade inlet. The key parameter of shape of the inlet was the opening angle.
进风口匹配与否是影响叶片入口处气流速度分布和涡流噪声的主要因素，而影响进风口形状的主要参数是张开角的大小。